Number 9, 2018
ИЗДАТЕЛЬСКИЙ ДОМ «ЛИТЕЙНОЕ ПРОИЗВОДСТВО»
Издательский дом «Литейное производство» выпускает два специализированных научно-технических журнала с периодичностью: «Литейное производство» – ежемесячно, «Металлургия машиностроения» – 1 раз в 2 месяца.
english version главная страница информация для рекламодателей заказать журналы
 
 
cover

Marukovich E.I., Stetsenko V.Y. About modifying of eutectic of castings from silumin
It is shown that sodium and strontium are not dissolved in silumin therefore cannot influence process of modifying of the eutectic dendritic crystals directly. In liquid silumin sodium is in a type of an emulsion, and strontium – in the form of a colloid. In case of the eutectic response vials of the selected hydrogen are created on the eutectic dendritic crystals, hindering with their ramifying. In case of the modifying processing of a melt of silumin vials of hydrogen are formed on a sodium emulsion or on a strontium colloid. It promotes ramifying of the eutectic dendritic crystals and receiving the modified eutectic.
Key words:Modifying, eutectic, silumin, dendritic crystals, emulsion, colloid, vials of hydrogen.

Eparkhin O.M., Alov V.A., Popkov A.N., Karpenko M.I., Karpenko V.M. Improving the quality and reliability of frictional iron details
This article describes ways of improvement the quality and reliability of frictional iron details with using of modifications and microalloying.
Key words:This article describes ways of improvement the quality and reliability of frictional iron details with using of modifications and microalloying.

Shcheretsky V.A., Zatulovsky A.S., Naboka E.A. New cast composites based on immiscible components
The article is devoted to the investigation of new wear-resistant composite materials with the Cu-alloy matrix reinforced with harder particles. The produced composite material has an increased wear resistance, which makes it possible to use it in loaded friction units.
Key words:Composite material, matrix, reinforcing phases, copper melt, steel plate.

Seredenko E.V. A complex effect of the cooling rate and the constant magnetic field on the grain size of a VAL10-type cast alloys
A complex effect of the cooling rate of the metal melt and the constant magnetic field on the grain size and structure uniformity of an Al-Cu cast alloy was investigated. Optimum values of the magnetic field induction at different cooling rates in the center and on the surface of a castingwere determined.
Key words:Magnetic field, cooling rate of a casting, magnetic field induction, grain, melt.

Kulikov V.Yu., Kvon Sv.S., Eryomin E.N., Kovalyova T.V., Adamova G.H. Influence of variable pressure on density and durability of sand-resin forms
The resin used for production of shell forms has high cost. For increase in adhesion of resin, its uniformity of distribution and, respectively, a possibility of decrease in her quantity in mix along with temperature influence pressure is used. Technological process for receiving forms looks as follows: after hashing sand-pitch mix is filled up in the bunker of the machine. Later capsizing of the bunker with mix on heated up to 240…250°C model plate is made. At the same time at the same time by means of press a plate pressure of 0,25 MPa moved. In 10 seconds pressure decreases to 0,2 MPa. In 10 seconds pressure increases up to 0,35 MPa. At the same time the shell form 10…14 mm thick is formed.
Key words:The shell, a form, casting, density, durability, pressure, pulverbakelit, adhesion, quality.

Aung Htut Thu, Zakharov A.I., Malyarov A.I. Technological properties of cold-hardening mixtures with liquid glass binder, obtained from agricultural wastes
The features of manufacturing technology and properties of liquid glass obtained with the use of rice husks are considered. The comparative technological properties of CHM, made with the use of industrial and experimental liquid glass.
Key words::Cold-hardening mixtures, liquid glass, rice husks.

Illarionov I.E., Babkin V.G., Gilmanshina Т.R., Kovaleva A.A., Lytkina S.I., Borisyuk V.A. Investigation of the properties of water suspensions on natural and activated graphites
In the liquid state, at the time of preparation and coating, complex colloidal systems are represented. Uniform distribution of graphite particles in water can be achieved by ensuring high sedimentation stability of the suspension, which is determined primarily by the colloidal-chemical properties of the graphite-water system: the wettability of graphite particles with water and the dispersion and state of the surface of the graphite particles. The purpose of this paper was to investigate the properties of suspensions depending on the quality of the filler. It is shown that substitution of natural graphite for the activated in the composition of the filler leads to an increase in the wettability of graphite by a binder composition, an increase in zeta-potenial, as a result of which suspensions made on the basis of activated graphite and bentonite are more stable.
Key words:Graphite, mechanoactivation, chemical activation, complex activation, wettability, suspensions.

Livshits V.B., Kazachkova O.A., Bobkova Е.S. Protective coatings for press-molds used in production of Al-alloy castings
A protective coating of press-molds used in production of Al-alloy castings was studied in the work. It has been found out that such a coating should have high thermal stability, mechanical and adhesive strength, an optimum heat-storage capacity and high processing characteristics. Pyrophyllite, which possesses these properties, can be used in production of Al-castings by injection molding and by all kinds of metallurgical working carried out under controlled pressure. This coating (with graphite additives) can be recommended for casting with crystallization under pressureof alloys, the melting point of which is ?1000 °C, for example, copper alloys.
Key words:Pyrophyllite, agalmatolite, casting with crystallization under pressure, properties, thermal stability.

Tkachenko S.S., Emelyanov V.O., Martynov K.V. Modular production of metal-cutting machines from standardized cast parts
The article outlines the concept of the domestic modular building of metal-cutting machinesbased on the decomposition of the basic parts of the equipment. The use of the "cloud" technologies in the field of the life cycle of metal-cutting machines is described.
Key words:Modular buildingof metal-cutting machines, 3D printing, basic parts ofmetal-cutting machines, "cloud" technologies, life cycle of metal-cutting machines.




Table of content

Naidek V.L. To the 60th anniversary of the Physical-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine

Marukovich E.I., Stetsenko V.Y. About modifying of eutectic of castings from silumin

Eparkhin O.M., Alov V.A., Popkov A.N., Karpenko M.I., Karpenko V.M. Improving the quality and reliability of frictional iron details

Shcheretsky V.A., Zatulovsky A.S., Naboka E.A. New cast composites based on immiscible components

Seredenko E.V. A complex effect of the cooling rate and the constant magnetic field on the grain size of a VAL10-type cast alloys

Kulikov V.Yu., Kvon Sv.S., Eryomin E.N., Kovalyova T.V., Adamova G.H. Influence of variable pressure on density and durability of sand-resin forms

Aung Htut Thu, Zakharov A.I., Malyarov A.I. Technological properties of cold-hardening mixtures with liquid glass binder, obtained from agricultural wastes

Illarionov I.E., Babkin V.G., Gilmanshina Т.R., Kovaleva A.A., Lytkina S.I., Borisyuk V.A. Investigation of the properties of water suspensions on natural and activated graphites

Livshits V.B., Kazachkova O.A., Bobkova Е.S. Protective coatings for press-molds used in production of Al-alloy castings

Tkachenko S.S., Emelyanov V.O., Martynov K.V. Modular production of metal-cutting machines from standardized cast parts


Русская версия

August 2018        October 2018


To archive


© Литейное производство, 2018
e-mail:liteinoe2006@yandex.ru